Skip to content

Roll-to-Roll Yield Estimator

Work out how many jobs fit on a roll, how much media they use, how much ends up as waste, and what the run costs. Enter the roll, add your jobs with quantities, set margins and rates, and press Calculate. Free, metric or imperial, and it runs in your browser.

Roll presets fill in example media prices. Replace them with what you actually pay.

Nesting Preview
Print area Waste Edge margin

How does it place jobs on the roll?

It uses shelf packing. Every piece is expanded by the bleed on each side, the pieces are sorted from largest to smallest, and each one is placed left to right in the current row. When a piece does not fit the row, a new row starts below it, separated by your gutter. With 90 degree rotation switched on, each piece may be turned if that lets it fit. The first piece in a row sets the row height, so the layout is fast and predictable but it is not true nesting. A tall row can leave a strip beside it that no remaining piece fits into.

How is waste calculated?

Media used is the full roll width times the layout length plus your trailing waste. Waste is media used minus the area of the placed pieces, so it covers the edge margins, the gutters, the gaps beside tall rows and the trailing waste. The area of each piece includes its bleed, so trimmed bleed is not counted as waste. Utilization is 100 percent minus waste percent.

How is the cost worked out?

  • Media is your roll price prorated by the length used, trailing waste included. The waste cost line shows how much of that media cost went to waste and is already inside the total.
  • Ink and laminate are charged per square metre of placed pieces, and finishing is charged per piece.
  • Print time is the placed area divided by your printer speed times the mode factor: 1 for Draft, 0.7 for Production and 0.45 for Quality. Enter the speed your printer reaches in Draft mode.
  • Machine and labor are charged by the hour over print time plus finishing time.
  • The rush multiplier is applied to total cost. The sell price is total cost divided by one minus the margin, so a 55 percent margin means profit is 55 percent of the price. The margin is capped at 95 percent.

What should I check before I trust a quote from it?

The roll presets fill in example media prices and a default 50 m roll length. Replace them with what you actually pay. The ink, machine and labor rates are also placeholders. The layout engine will not beat a good operator with a RIP nesting module on irregular shapes, so treat the yield as a planning number for rectangular jobs and confirm it in your RIP before you commit to a price.

Frequently asked questions

What does the Roll-to-Roll Yield Estimator calculate?

For a roll and a list of jobs it works out how many pieces fit, how much roll length and media area the run uses, how much of that becomes waste, and what the run costs and sells for. It also estimates print time and flags when another roll width would raise utilization.

How does it place jobs on the roll?

It adds the bleed to every piece, sorts the pieces from largest to smallest, and places them left to right in rows with your gutter between them. A piece that does not fit the current row starts a new row. With 90 degree rotation allowed, a piece can be turned if that lets it fit. This is shelf packing for rectangles, not true nesting.

How is waste calculated?

Waste is the media used minus the area of the placed pieces. Media used is the full roll width times the layout length plus the trailing waste you enter. Edge margins, gutters, gaps beside tall rows and trailing waste all count as waste. Bleed is part of each piece, so it does not count as waste.

Are the media prices in the roll presets real?

No. They are example values so the cost section is not empty. Replace the media cost per roll, ink cost, machine rate and labor rate with your own numbers before you rely on the sell price.

Does it work in inches and feet?

Yes. Switch Units to Imperial and every field converts, including the jobs already entered. Roll presets keep the unit you have selected. The results show square feet and feet in Imperial mode.

Why were some jobs skipped?

A piece is skipped when it is wider than the printable roll width in every allowed orientation, or when it does not fit in the roll length that remains. The tool also stops at 2000 pieces per run, so split very large orders into batches.

Are my jobs and prices sent anywhere?

No. The calculation runs in your browser and nothing is sent to a server or saved. Reloading the page resets all fields.

Related on Printing TLDR: the large format printing tools hub.

Running DTF next to wide format?

The DTF Printing Profit Blueprint covers cost and pricing for the DTF side of the shop: 122 pages and 8 Excel templates with 170 formulas.

See the ebook

Last reviewed: 19 October 2026 · Reviewed by

Scroll to Top